![]() I took the freedom to assign the 'Zoom to Fit' short cut to the central Zoom button on the device. Maybe it's obvious, but for newbies like me: this only works in the Mackie Control Mode, for which you will might have to update your device with a free firmware patch 1.02, and go through a special boot cycle. So, I can confirm that your setup also works for the Logic Control. Thank you so much for going into this! And what a nice bonus that you added the overlay! (A decent AppleScript implementation, or an otherwise accessible API would be great as well),Īnyway, after programming some short cuts with Midi Monitor and Midi Stroke, I got bored, and ran into this post. I think it's really strange there is no native support for control surfaces in FCPX, and I expect/hope that this is one of those omissions that Apple will be repairing as they did with so many things. It just seemed like a good way to make use of the mark 1 and mark 2 consoles.Would this be a proof of synchronicity? Or a Higher Being? I just found a second hand Mackie Logic Control -really cheap: 100 euros- and tried to figure out how to make it work with FCPX. I wouldn't say that what I did is a perfect substitute for a fully functioning console, but the functionality of the keys is identical. This seems unlikely, but possible.Īt some point I'll start another thread, after I get the programming of the shuttle dialed in. It's also possible that a portion of the circuitry in the console had failed in someway. I spent a while trying to get the mk 1 going on a PC and mac, simply couldn't get them to function properly. This isn't just a matter of "feel", but directly effects functionality in the sense of just being able to edit without constantly thinking about the interface. In addition to layout, the keys themselves on the lightworks console are very sensitive and very precise. Having picked up a contour shuttle to try out, it is a far cry from the console. The primary difference that I see is that the ergonomics of the lightworks console are second to none. I'm also looking for a nonworking mk2 or mk3 to try out in a similar manner. I had to glue together a couple of plastic joins that had cracked. The caveat is a 25 year old console needs delicate handling when disassembled. If anyone is interested I can post more details and the code. Then it was just a matter of assigning the keys to the correct keyboard shortcuts. The code, adapted code I found on arduino sites, basically sends a midi note for each key on the console, and then an awesome bit of software called midistroke translates the midi value into a keystroke. I bypassed the electronics of the console and hooked the wires from the switches directly into a small arduino controller (which the computer sees as a midi controller. this post should go here.Īs a follow up, I finally gave up dealing with serial/USB adaptors and finally got an mk 1 to work on a Mac system by essentially turning it into a midi controller. The ipac and minipac by ultimarc look pretty cool and it seems like it should be relatively straightforward to build a custom controller box, wiring the switches into the control board, USB to computer and then run it through the keyboard shortcuts in Lightworks. There is also a whole world of gaming DIY arcade controllers, which again are a bunch of switches run through a usb/keyboard controller. But the design of the Consoles are much better than the contours, at least to me.Ĭheck out Midi fighter - arcade button midi controllers. it requires some soldering but might prove to be a good approach to getting mark 1 consoles useable, though there might be problems with the shuttle. ![]() So I'm mounting the contour board into the Lightworks console and running the lines to the contour switches through the Console connectors. Essentially, the old consoles are a bunch of switches and a potentiometer working in concert with the software. Just spent a lot of time getting a shuttle pro to work smoothly with premiere- a real pain, whereas it works beautifully straightaway in Lightworks.Īnother option could be something I'm actually trying right now: putting a stripped down contour shuttle into a mark 1 console. Lightworks is far better than any other NLE for this, since it has assigned keyboard shortcuts for each playback speed, instead of the usual Shift+l scenario. The difficulty I have had is getting shuttle and jog wheels to work smoothly, but in lightworks it should be as simple as assigning the correct keyboard shortcut to each position or value of the wheel. ![]() ![]() there are probably more out there.īasically, you just assign a midi keystroke to a keyboard shortcut and the software bridges the gap. ![]() Midi-stroke works well, and is freeware, and I think controller mate is another. There are several programs that will translate midi signals into keystrokes. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |